# Boots from SD older rk3399-eflasher-buildroot-4.19-20211231.img.zip

DDR Version 1.24 20191016
In
Channel 0: DDR3, 800MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
no stride
ch 0 ddrconfig = 0x101, ddrsize = 0x20
pmugrf_os_reg[2] = 0x10006281, stride = 0x17
OUT
Boot1 Release Time: May 29 2020 17:36:36, version: 1.26
CPUId = 0x0
ChipType = 0x10, 338
SdmmcInit=2 0
BootCapSize=100000
UserCapSize=14910MB
FwPartOffset=2000 , 100000
mmc0:cmd5,20
SdmmcInit=0 0
BootCapSize=0
UserCapSize=61056MB
FwPartOffset=2000 , 0
run on sd0
StorageInit ok = 353195
SecureMode = 0
SecureInit read PBA: 0x4
SecureInit read PBA: 0x404
SecureInit read PBA: 0x804
SecureInit read PBA: 0xc04
SecureInit read PBA: 0x1004
SecureInit read PBA: 0x1404
SecureInit read PBA: 0x1804
SecureInit read PBA: 0x1c04
SecureInit ret = 0, SecureMode = 0
atags_set_bootdev: ret:(0)
GPT 0x3335db8 signature is wrong
recovery gpt...
GPT part:  0, name:            uboot, start:0x4000, size:0x2000
GPT part:  1, name:            trust, start:0x6000, size:0x2000
GPT part:  2, name:             misc, start:0x8000, size:0x2000
GPT part:  3, name:             dtbo, start:0xa000, size:0x2000
GPT part:  4, name:         resource, start:0xc000, size:0x8000
GPT part:  5, name:           kernel, start:0x14000, size:0x14000
GPT part:  6, name:             boot, start:0x28000, size:0x18000
GPT part:  7, name:           rootfs, start:0x40000, size:0x340000
GPT part:  8, name:         userdata, start:0x380000, size:0x73bffdf
recovery gpt success!
find part:uboot OK. first_lba:0x4000.
find part:trust OK. first_lba:0x6000.
Trust Addr:0x6000, 0x58334c42
No find bl30.bin
Load uboot, ReadLba = 4000
Load OK, addr=0x200000, size=0x8705c
RunBL31 0x40000 @ 508285 us
NOTICE:  BL31: v1.3(debug):734d84297
NOTICE:  BL31: Built : 15:30:40, Dec 12 2019
NOTICE:  BL31: Rockchip release version: v1.1
INFO:    GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3
INFO:    Using opteed sec cpu_context!
INFO:    boot cpu mask: 0
INFO:    plat_rockchip_pmu_init(1190): pd status 3e
INFO:    BL31: Initializing runtime services
INFO:    BL31: Initializing BL32
INF [0x0] TEE-CORE:init_primary_helper:337: Initializing (1.1.0-195-g8f090d20 #6 Fri Dec  7 06:11:20 UTC 2018 aarch64)

INF [0x0] TEE-CORE:init_primary_helper:338: Release version: 1.2

INF [0x0] TEE-CORE:init_teecore:83: teecore inits done
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x200000
INFO:    SPSR = 0x3c9


U-Boot 2014.10-RK3399-06 (Jun 03 2021 - 20:58:00)

CPU: rk3399
cpu version = 0
CPU's clock information:
    aplll = 816000000HZ
    apllb = 24000000HZ
    gpll = 800000000HZ
               aclk_periph_h = 133333333HZ, hclk_periph_h = 66666666HZ, pclk_periph_h = 33333333HZ
               aclk_periph_l0 = 266666666HZ, hclk_periph_l0 = 88888888HZ, pclk_periph_l0 = 44444444HZ
               hclk_periph_l1 = 100000000HZ, pclk_periph_l1 = 50000000HZ
    cpll = 800000000HZ
    dpll = 800000000HZ
    vpll = 24000000HZ
    npll = 24000000HZ
    ppll = 676000000HZ
Board:	Rockchip platform Board
Uboot as second level loader
DRAM:  Found dram banks: 1
Adding bank:0000000000200000(000000003fe00000)
Reserve memory for trust os.
dram reserve bank: base = 0x08400000, size = 0x01e00000
128 MiB
SdmmcInit = 0 0
SDCard Boot.
storage init OK!
Using default environment

Writing env to storage... 
done
GetParam
Load FDT from resource image.
no key node
can't find dts node for fixed
usb bc: can find node by path: /dwc-control-usb/usb_bc
pmic:rk808
can't find dts node for pwm1
set pwm voltage ok,pwm_id =2 vol=900000,pwm_value=16
Can't find dts node for fuel guage cw201x
can't find dts node for ec-battery
Can't find dts node for charger bq25700
invalide header tag
ca head not found
SecureBootEn = 0, SecureBootLock = 0

#Boot ver: 2020-03-16#1.19
empty serial no.
Writing env to storage... 
done
normal boot.
checkKey
vbus = 1
no fuel gauge found
no fuel gauge found
Rockchip UBOOT DRM driver version: develop-v1.0.0
failed to find panel driver
delay prepare[20] unprepare[0] enable[20] disable[0]
read logo on state from dts [1]
no fuel gauge found
Monitor has basic audio support
drm_rk_selete_output; fail get baseparameter
rk lcdc - 0 dclk set: dclk = 148500000HZ, pll select = 0, div = 1
rockchip_panel_prepare: failed to find panel prepare funcs
Non-CEA mode (1920x1080) used in HDMI
dw_hdmi_setup HDMI mode
rockchip_panel_enable: failed to find panel prepare funcs
failed to find display timing
Hit any key to stop autoboot:  0 
load fdt from resouce.
error init vendor storage.
vendor read error!
Set oem_unlocked=0Secure Boot state: 0
kernel   @ 0x00280000 (0x01419200)
ramdisk  @ 0x04bf0000 (0x0044db88)
bootrk: do_bootm_linux...
   Loading Device Tree to 0000000004600000, end 000000000461c9c8 ... OK
Add bank:0000000000200000, 0000000008200000
Add bank:000000000a200000, 0000000035e00000
WARNING: could not set reg FDT_ERR_BADOFFSET.

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.4.179 (root@jensen) (gcc version 11.1.0 (ctng-1.24.0-345g-FA) ) #2 SMP Mon Dec 20 18:42:11 CST 2021
[    0.000000] Boot CPU: AArch64 Processor [410fd034]
[    0.000000] earlycon: Early serial console at MMIO32 0xff1a0000 (options '')
[    0.000000] bootconsole [uart0] enabled
[    0.000000] Panel: using mode 1920x1080 for HDMI1920x1080
[    0.000000] efi: Getting EFI parameters from FDT:
[    0.000000] efi: UEFI not found.
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: Trusted OS migration not required
[    0.000000] PERCPU: Embedded 21 pages/cpu @ffffffc03fee9000 s46376 r8192 d31448 u86016
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: enabling workaround for ARM erratum 845719
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 249864
[    0.000000] Kernel command line: earlycon=uart8250,mmio32,0xff1a0000 swiotlb=1 console=ttyFIQ0 rootwait coherent_pool=1m root=/dev/mmcblk0p2 rw rootfstype=ext4 lcd=HDMI1920x1080 storagemedia=sd uboot_logo=0x02000000@0x3dc00000 loader.timestamp=2021-06-03_20:58:00 SecureBootCheckOk=0
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[    0.000000] software IO TLB: mapped [mem 0x3fe21000-0x3fe61000] (0MB)
[    0.000000] Memory: 967144K/1015808K available (11708K kernel code, 1380K rwdata, 6356K rodata, 1088K init, 1923K bss, 48664K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)
[    0.000000]     vmalloc : 0xffffff8008000000 - 0xffffffbdbfff0000   (   246 GB)
[    0.000000]       .init : 0xffffff8009230000 - 0xffffff8009340000   (  1088 KB)
[    0.000000]       .text : 0xffffff8008080000 - 0xffffff8008bf0000   ( 11712 KB)
[    0.000000]     .rodata : 0xffffff8008bf0000 - 0xffffff8009230000   (  6400 KB)
[    0.000000]       .data : 0xffffff8009340000 - 0xffffff8009499200   (  1381 KB)
[    0.000000]     vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000   (     8 GB maximum)
[    0.000000]               0xffffffbdc0008000 - 0xffffffbdc1000000   (    15 MB actual)
[    0.000000]     fixed   : 0xffffffbffe7fb000 - 0xffffffbffec00000   (  4116 KB)
[    0.000000]     PCI I/O : 0xffffffbffee00000 - 0xffffffbfffe00000   (    16 MB)
[    0.000000]     memory  : 0xffffffc000200000 - 0xffffffc040000000   (  1022 MB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	Build-time adjustment of leaf fanout to 64.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=6.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=6
[    0.000000] NR_IRQS:64 nr_irqs:64 0
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] ITS: /interrupt-controller@fee00000/interrupt-controller@fee20000
[    0.000000] ITS: allocated 65536 Devices @3e880000 (psz 64K, shr 0)
[    0.000000] ITS: using cache flushing for cmd queue
[    0.000000] GIC: using LPI property table @0x000000003e900000
[    0.000000] ITS: Allocated 1792 chunks for LPIs
[    0.000000] CPU0: found redistributor 0 region 0:0x00000000fef00000
[    0.000000] CPU0: using LPI pending table @0x000000003e910000
[    0.000000] GIC: using cache flushing for LPI property table
[    0.000000] GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0[0] /cpus/cpu@1[1] /cpus/cpu@2[2] /cpus/cpu@3[3] }
[    0.000000] GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@100[4] /cpus/cpu@101[5] }
[    0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop0_frac as parent of dclk_vop0, rate changes may not work
[    0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop1_frac as parent of dclk_vop1, rate changes may not work
[    0.000000] rockchip_cpuclk_pre_rate_change: limiting alt-divider 33 to 31
[    0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.002103] Console: colour dummy device 80x25
[    0.002549] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=24000)
[    0.003539] pid_max: default: 32768 minimum: 301
[    0.004086] Security Framework initialized
[    0.004496] AppArmor: AppArmor disabled by boot time parameter
[    0.005092] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
[    0.005744] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
[    0.007102] Initializing cgroup subsys io
[    0.007500] Initializing cgroup subsys memory
[    0.007953] Initializing cgroup subsys devices
[    0.008387] Initializing cgroup subsys freezer
[    0.008820] Initializing cgroup subsys net_cls
[    0.009259] Initializing cgroup subsys perf_event
[    0.009716] Initializing cgroup subsys net_prio
[    0.010160] Initializing cgroup subsys hugetlb
[    0.010599] Initializing cgroup subsys pids
[    0.011032] ftrace: allocating 36554 entries in 143 pages
[    0.112638] sched-energy: Sched-energy-costs installed from DT
[    0.113243] CPU0: update cpu_capacity 401
[    0.113671] ASID allocator initialised with 32768 entries
[    0.117114] PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
[    0.118528] Platform MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
[    0.119836] EFI services will not be available.
[    0.121237] Detected VIPT I-cache on CPU1
[    0.121269] CPU1: found redistributor 1 region 0:0x00000000fef20000
[    0.121305] CPU1: using LPI pending table @0x000000003eb00000
[    0.121349] CPU1: update cpu_capacity 401
[    0.121352] CPU1: Booted secondary processor [410fd034]
[    0.121923] Detected VIPT I-cache on CPU2
[    0.121942] CPU2: found redistributor 2 region 0:0x00000000fef40000
[    0.121974] CPU2: using LPI pending table @0x000000003eb20000
[    0.122000] CPU2: update cpu_capacity 401
[    0.122003] CPU2: Booted secondary processor [410fd034]
[    0.122540] Detected VIPT I-cache on CPU3
[    0.122558] CPU3: found redistributor 3 region 0:0x00000000fef60000
[    0.122591] CPU3: using LPI pending table @0x000000003eb80000
[    0.122616] CPU3: update cpu_capacity 401
[    0.122619] CPU3: Booted secondary processor [410fd034]
[    0.123155] Detected PIPT I-cache on CPU4
[    0.123183] CPU4: found redistributor 100 region 0:0x00000000fef80000
[    0.123224] CPU4: using LPI pending table @0x000000003ebb0000
[    0.123262] CPU4: update cpu_capacity 1024
[    0.123265] CPU4: Booted secondary processor [410fd082]
[    0.123834] Detected PIPT I-cache on CPU5
[    0.123851] CPU5: found redistributor 101 region 0:0x00000000fefa0000
[    0.123889] CPU5: using LPI pending table @0x000000003ebf0000
[    0.123913] CPU5: update cpu_capacity 1024
[    0.123916] CPU5: Booted secondary processor [410fd082]
[    0.124000] Brought up 6 CPUs
[    0.136411] SMP: Total of 6 processors activated.
[    0.136864] CPU features: detected feature: GIC system register CPU interface
[    0.137555] CPU features: detected feature: 32-bit EL0 Support
[    0.138116] CPU: All CPU(s) started at EL2
[    0.138548] alternatives: patching kernel code
[    0.140288] devtmpfs: initialized
[    0.157364] DMI not present or invalid.
[    0.158035] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[    0.158984] futex hash table entries: 2048 (order: 5, 131072 bytes)
[    0.160106] pinctrl core: initialized pinctrl subsystem
[    0.161356] NET: Registered protocol family 16
[    0.166030] cpuidle: using governor ladder
[    0.171042] cpuidle: using governor menu
[    0.171438] Registered FIQ tty driver
[    0.171883] vdso: 2 pages (1 code @ ffffff8008bf6000, 1 data @ ffffff8009344000)
[    0.172618] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.173816] DMA: preallocated 1024 KiB pool for atomic allocations
[    0.196664] console [pstore-1] enabled
[    0.197037] pstore: Registered ramoops as persistent store backend
[    0.197628] ramoops: attached 0xf0000@0x110000, ecc: 0/0
[    0.200854] console [ttyFIQ0] enabled
[    0.200854] console [ttyFIQ0] enabled
[    0.201546] bootconsole [uart0] disabled
[    0.201546] bootconsole [uart0] disabled
[    0.202444] Registered fiq debugger ttyFIQ0
[    0.216645] vcc_lcd: supplied by vcc5v0_sys
[    0.238792] iommu: Adding device ff650000.vpu_service to group 0
[    0.239419] iommu: Adding device ff660000.rkvdec to group 1
[    0.240018] iommu: Adding device ff8f0000.vop to group 2
[    0.240578] iommu: Adding device ff900000.vop to group 3
[    0.241131] iommu: Adding device ff910000.rkisp1 to group 4
[    0.241716] iommu: Adding device ff920000.rkisp1 to group 5
[    0.242707] rk_iommu ff650800.iommu: can't get sclk
[    0.243396] rk_iommu ff660480.iommu: can't get sclk
[    0.244026] rk_iommu ff8f3f00.iommu: can't get sclk
[    0.244614] rk_iommu ff903f00.iommu: can't get sclk
[    0.245202] rk_iommu ff914000.iommu: can't get sclk
[    0.245776] rk_iommu ff924000.iommu: can't get sclk
[    0.246508] SCSI subsystem initialized
[    0.247172] usbcore: registered new interface driver usbfs
[    0.247711] usbcore: registered new interface driver hub
[    0.248260] usbcore: registered new device driver usb
[    0.248773] media: Linux media interface: v0.10
[    0.249203] Linux video capture interface: v2.00
[    0.249654] pps_core: LinuxPPS API ver. 1 registered
[    0.250106] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.250922] PTP clock support registered
[    0.251380] dmi: Firmware registration failed.
[    0.252860] Advanced Linux Sound Architecture Driver Initialized.
[    0.253899] Bluetooth: Core ver 2.21
[    0.254240] NET: Registered protocol family 31
[    0.254647] Bluetooth: HCI device and connection manager initialized
[    0.255217] Bluetooth: HCI socket layer initialized
[    0.255661] Bluetooth: L2CAP socket layer initialized
[    0.256122] Bluetooth: SCO socket layer initialized
[    0.256893] NetLabel: Initializing
[    0.257201] NetLabel:  domain hash size = 128
[    0.257588] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.258069] NetLabel:  unlabeled traffic allowed by default
[    0.258832] rockchip-cpuinfo cpuinfo: Serial		: 3293b0852c213abe
[    0.259782] clocksource: Switched to clocksource arch_sys_counter
[    0.299882] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
[    0.300819] NET: Registered protocol family 2
[    0.301639] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    0.302340] TCP bind hash table entries: 8192 (order: 6, 262144 bytes)
[    0.303162] TCP: Hash tables configured (established 8192 bind 8192)
[    0.303812] UDP hash table entries: 512 (order: 3, 49152 bytes)
[    0.304376] UDP-Lite hash table entries: 512 (order: 3, 49152 bytes)
[    0.305139] NET: Registered protocol family 1
[    0.305863] RPC: Registered named UNIX socket transport module.
[    0.306392] RPC: Registered udp transport module.
[    0.306823] RPC: Registered tcp transport module.
[    0.307244] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.308494] Trying to unpack rootfs image as initramfs...
[    0.528922] Freeing initrd memory: 4404K
[    0.529577] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[    0.530401] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
[    0.534025] audit: initializing netlink subsys (disabled)
[    0.534541] audit: type=2000 audit(0.454:1): initialized
[    0.535416] Initialise system trusted keyring
[    0.536214] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.543640] VFS: Disk quotas dquot_6.6.0
[    0.544158] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.546213] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.547764] NFS: Registering the id_resolver key type
[    0.548254] Key type id_resolver registered
[    0.548631] Key type id_legacy registered
[    0.549200] fuse init (API version 7.23)
[    0.555626] Key type asymmetric registered
[    0.556018] Asymmetric key parser 'x509' registered
[    0.556620] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    0.557436] io scheduler noop registered
[    0.557810] io scheduler deadline registered
[    0.558315] io scheduler cfq registered (default)
[    0.560258] phy phy-ff770000.syscon:usb2-phy@e460.1: Failed to get VBUS supply regulator
[    0.566839] rockchip-pcie f8000000.pcie: no vpcie3v3 regulator found
[    0.567408] rockchip-pcie f8000000.pcie: no vpcie1v8 regulator found
[    0.567984] rockchip-pcie f8000000.pcie: no vpcie0v9 regulator found
[    0.568548] rockchip-pcie f8000000.pcie: missing "memory-region" property
[    0.569158] PCI host bridge /pcie@f8000000 ranges:
[    0.569593]   MEM 0xfa000000..0xfbdfffff -> 0xfa000000
[    0.570061]    IO 0xfbe00000..0xfbefffff -> 0xfbe00000
[    1.090823] rockchip-pcie f8000000.pcie: PCIe link training gen1 timeout!
[    1.091436] rockchip-pcie f8000000.pcie: deferred probe failed
[    1.092169] rockchip-pcie: probe of f8000000.pcie failed with error -110
[    1.093808] backlight supply power not found, using dummy regulator
[    1.095024] rk-vcodec ff650000.vpu_service: no regulator for vcodec
[    1.095893] rk-vcodec ff650000.vpu_service: probe device
[    1.096594] rk-vcodec ff650000.vpu_service: drm allocator with mmu enabled
[    1.097743] rk-vcodec ff650000.vpu_service: could not find power_model node
[    1.098379] rk-vcodec ff650000.vpu_service: init success
[    1.099053] rk-vcodec ff660000.rkvdec: no regulator for vcodec
[    1.099972] rk-vcodec ff660000.rkvdec: probe device
[    1.100584] rk-vcodec ff660000.rkvdec: drm allocator with mmu enabled
[    1.101533] rk-vcodec ff660000.rkvdec: could not find power_model node
[    1.102123] rk-vcodec ff660000.rkvdec: init success
[    1.103991] dma-pl330 ff6d0000.dma-controller: Loaded driver for PL330 DMAC-241330
[    1.104661] dma-pl330 ff6d0000.dma-controller: 	DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12
[    1.106827] dma-pl330 ff6e0000.dma-controller: Loaded driver for PL330 DMAC-241330
[    1.107495] dma-pl330 ff6e0000.dma-controller: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
[    1.108556] rockchip-system-monitor rockchip-system-monitor: system monitor probe
[    1.110499] Serial: 8250/16550 driver, 5 ports, IRQ sharing disabled
[    1.111669] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 38, base_baud = 1500000) is a 16550A
[    1.112976] ff370000.serial: ttyS4 at MMIO 0xff370000 (irq = 40, base_baud = 1500000) is a 16550A
[    1.114767] [drm] Initialized drm 1.1.0 20060810
[    1.118753] [drm] Rockchip DRM driver version: v1.0.1
[    1.121602] mali ff9a0000.gpu: Failed to get regulator
[    1.122071] mali ff9a0000.gpu: Power control initialization failed
[    1.122951] Unable to detect cache hierarchy for CPU 0
[    1.128026] brd: module loaded
[    1.133539] loop: module loaded
[    1.134355] zram: Added device: zram0
[    1.137259] rk_gmac-dwmac fe300000.ethernet: clock input or output? (input).
[    1.137908] rk_gmac-dwmac fe300000.ethernet: TX delay(0x28).
[    1.138414] rk_gmac-dwmac fe300000.ethernet: RX delay(0x11).
[    1.138941] rk_gmac-dwmac fe300000.ethernet: integrated PHY? (no).
[    1.139640] rk_gmac-dwmac fe300000.ethernet: cannot get clock clk_mac_speed
[    1.140267] rk_gmac-dwmac fe300000.ethernet: clock input from PHY
[    1.145818] rk_gmac-dwmac fe300000.ethernet: init for RGMII
[    1.146418] stmmac - user ID: 0x10, Synopsys ID: 0x35
[    1.146872]  Ring mode enabled
[    1.147144]  DMA HW capability register supported
[    1.147542]  Normal descriptors
[    1.147857]  RX Checksum Offload Engine supported (type 2)
[    1.148347]  TX Checksum insertion supported
[    1.148723]  Wake-Up On Lan supported
[    1.149090]  Enable RX Mitigation via HW Watchdog Timer
[    1.219312] libphy: stmmac: probed
[    1.219628] eth%d: PHY ID 001cc915 at 0 IRQ POLL (stmmac-0:00) active
[    1.220207] eth%d: PHY ID 001cc915 at 1 IRQ POLL (stmmac-0:01)
[    1.222050] PPP generic driver version 2.4.2
[    1.222584] Rockchip WiFi SYS interface (V1.00) ... 
[    1.223110] usbcore: registered new interface driver asix
[    1.223628] usbcore: registered new interface driver ax88179_178a
[    1.224206] usbcore: registered new interface driver cdc_ether
[    1.224761] usbcore: registered new interface driver qmi_wwan
[    1.226568] rockchip-dwc3 usb0: failed to get drvdata dwc3
[    1.231699] rockchip-dwc3 usb1: fail to get drvdata hcd
[    1.233210] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.233808] ehci-pci: EHCI PCI platform driver
[    1.234250] ehci-platform: EHCI generic platform driver
[    1.238507] ehci-platform fe3c0000.usb: EHCI Host Controller
[    1.239059] ehci-platform fe3c0000.usb: new USB bus registered, assigned bus number 1
[    1.239865] ehci-platform fe3c0000.usb: irq 30, io mem 0xfe3c0000
[    1.245797] ehci-platform fe3c0000.usb: USB 2.0 started, EHCI 1.00
[    1.246487] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.247098] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.247740] usb usb1: Product: EHCI Host Controller
[    1.248184] usb usb1: Manufacturer: Linux 4.4.179 ehci_hcd
[    1.248676] usb usb1: SerialNumber: fe3c0000.usb
[    1.249540] hub 1-0:1.0: USB hub found
[    1.249937] hub 1-0:1.0: 1 port detected
[    1.250837] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.251397] ohci-platform: OHCI generic platform driver
[    1.252313] ohci-platform fe3e0000.usb: Generic Platform OHCI controller
[    1.252955] ohci-platform fe3e0000.usb: new USB bus registered, assigned bus number 2
[    1.253718] ohci-platform fe3e0000.usb: irq 31, io mem 0xfe3e0000
[    1.308928] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    1.309527] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.310180] usb usb2: Product: Generic Platform OHCI controller
[    1.310707] usb usb2: Manufacturer: Linux 4.4.179 ohci_hcd
[    1.311206] usb usb2: SerialNumber: fe3e0000.usb
[    1.312017] hub 2-0:1.0: USB hub found
[    1.312373] hub 2-0:1.0: 1 port detected
[    1.313631] usbcore: registered new interface driver cdc_acm
[    1.314149] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    1.314892] usbcore: registered new interface driver cdc_wdm
[    1.315428] usbcore: registered new interface driver uas
[    1.315964] usbcore: registered new interface driver usb-storage
[    1.316564] usbcore: registered new interface driver usbserial
[    1.317117] usbcore: registered new interface driver usbserial_generic
[    1.317710] usbserial: USB Serial support registered for generic
[    1.318287] usbcore: registered new interface driver ch341
[    1.318805] usbserial: USB Serial support registered for ch341-uart
[    1.319383] usbcore: registered new interface driver cp210x
[    1.319903] usbserial: USB Serial support registered for cp210x
[    1.320467] usbcore: registered new interface driver ftdi_sio
[    1.321014] usbserial: USB Serial support registered for FTDI USB Serial Device
[    1.321713] usbcore: registered new interface driver option
[    1.322232] usbserial: USB Serial support registered for GSM modem (1-port)
[    1.322930] usbcore: registered new interface driver pl2303
[    1.323440] usbserial: USB Serial support registered for pl2303
[    1.324010] usbcore: registered new interface driver qcserial
[    1.324542] usbserial: USB Serial support registered for Qualcomm USB modem
[    1.325507] mousedev: PS/2 mouse device common for all mice
[    1.326515] <<-GTP-INFO->> GTP driver installing
[    1.327322] sensor_register_slave:mma8452,id=17
[    1.327727] sensor_register_slave:lis3dh,id=7
[    1.328136] sensor_register_slave:mma7660,id=18
[    1.328539] sensor_register_slave:lsm303d,id=22
[    1.328951] sensor_register_slave:mpu6880_acc,id=24
[    1.329388] sensor_register_slave:mpu6500_acc,id=25
[    1.329834] sensor_register_slave:lsm330_acc,id=26
[    1.330260] sensor_register_slave:akm8975,id=30
[    1.330662] sensor_register_slave:akm8963,id=31
[    1.331072] sensor_register_slave:l3g4200d,id=45
[    1.331486] sensor_register_slave:l3g20d,id=46
[    1.331894] sensor_register_slave:ewtsa,id=47
[    1.332285] sensor_register_slave:lsm330_gyro,id=51
[    1.332722] sensor_register_slave:cm3217,id=53
[    1.333132] sensor_register_slave:cm3218,id=54
[    1.333969] i2c /dev entries driver
[    1.335545] fan53555-regulator 0-0040: FAN53555 Option[8] Rev[1] Detected!
[    1.336220] fan53555-reg: supplied by vcc3v3_sys
[    1.338964] fan53555-regulator 0-0041: FAN53555 Option[8] Rev[1] Detected!
[    1.339612] fan53555-reg: supplied by vcc3v3_sys
[    1.342289] rk808 0-001b: Pmic Chip id: 0x0
[    1.345897] rk808-regulator rk808-regulator: there is no dvs0 gpio
[    1.346497] rk808-regulator rk808-regulator: there is no dvs1 gpio
[    1.347127] DCDC_REG1: supplied by vcc3v3_sys
[    1.348232] DCDC_REG2: supplied by vcc3v3_sys
[    1.349163] DCDC_REG3: supplied by vcc3v3_sys
[    1.349836] DCDC_REG4: supplied by vcc3v3_sys
[    1.350669] LDO_REG1: supplied by vcc3v3_sys
[    1.352156] LDO_REG2: supplied by vcc3v3_sys
[    1.353494] LDO_REG3: supplied by vcc3v3_sys
[    1.354863] LDO_REG4: supplied by vcc3v3_sys
[    1.356206] LDO_REG5: supplied by vcc3v3_sys
[    1.357545] LDO_REG6: supplied by vcc3v3_sys
[    1.358899] LDO_REG7: supplied by vcc3v3_sys
[    1.360245] LDO_REG8: supplied by vcc3v3_sys
[    1.361594] SWITCH_REG1: supplied by vcc3v3_sys
[    1.362290] SWITCH_REG2: supplied by vcc3v3_sys
[    1.366118] rk808-rtc rk808-rtc: rtc core: registered rk808-rtc as rtc0
[    1.367125] rk3x-i2c ff3c0000.i2c: Initialized RK3xxx I2C bus at ffffff800994c000
[    1.368525] rk3x-i2c ff110000.i2c: Initialized RK3xxx I2C bus at ffffff800994e000
[    1.369741] rk3x-i2c ff120000.i2c: Initialized RK3xxx I2C bus at ffffff8009950000
[    1.370798] rk3x-i2c ff160000.i2c: Initialized RK3xxx I2C bus at ffffff8009952000
[    1.372525] fusb302 4-0022: Can't get property of role, set role to default DRP
[    1.376400] fusb302 4-0022: port 0 probe success with role ROLE_MODE_DRP, try_role ROLE_MODE_NONE
[    1.377331] input: Typec_Headphone as /devices/platform/ff3d0000.i2c/i2c-4/4-0022/input/input0
[    1.378571] rk3x-i2c ff3d0000.i2c: Initialized RK3xxx I2C bus at ffffff8009954000
[    1.380340] IR NEC protocol handler initialized
[    1.382789] Boot mode: coldboot
[    1.384217] rk_tsadcv2_temp_to_code: Invalid conversion table: code=1023, temperature=2147483647
[    1.385160] rockchip-thermal ff260000.tsadc: tsadc is probed successfully!
[    1.386348] dw_wdt ff848000.watchdog: Should better to setup a 'resets' property in dt, that must been named with reset
[    1.387682] device-mapper: uevent: version 1.0.3
[    1.388382] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
[    1.389294] Bluetooth: Virtual HCI driver ver 1.5
[    1.389833] Bluetooth: HCI UART driver ver 2.3
[    1.390234] Bluetooth: HCI UART protocol H4 registered
[    1.390690] Bluetooth: HCI UART protocol BCSP registered
[    1.391168] Bluetooth: HCI UART protocol LL registered
[    1.391624] Bluetooth: HCI UART protocol ATH3K registered
[    1.392110] Bluetooth: HCI UART protocol Three-wire (H5) registered
[    1.392788] Bluetooth: HCI UART protocol BCM registered
[    1.393310] usbcore: registered new interface driver bfusb
[    1.393856] usbcore: registered new interface driver btusb
[    1.394793] cpu cpu0: bin=1
[    1.395090] cpu cpu0: leakage=17
[    1.396341] cpu cpu0: Failed to get pvtm
[    1.396743] cpu cpu0: bin-scale=34
[    1.397301] cpu cpu4: bin=1
[    1.397596] cpu cpu4: leakage=31
[    1.398537] cpu cpu4: Failed to get pvtm
[    1.398942] cpu cpu4: bin-scale=17
[    1.400231] cpu cpu0: avs=0
[    1.400571] cpu cpu0: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0
[    1.401691] cpu cpu0: failed to find power_model node
[    1.403053] cpu cpu4: avs=0
[    1.403398] cpu cpu4: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0
[    1.405329] cpu cpu4: failed to find power_model node
[    1.406588] sdhci: Secure Digital Host Controller Interface driver
[    1.407162] sdhci: Copyright(c) Pierre Ossman
[    1.407554] Synopsys Designware Multimedia Card Interface Driver
[    1.408953] dwmmc_rockchip fe310000.dwmmc: IDMAC supports 32-bit address mode.
[    1.409624] dwmmc_rockchip fe310000.dwmmc: Using internal DMA controller.
[    1.410239] dwmmc_rockchip fe310000.dwmmc: Version ID is 270a
[    1.410801] dwmmc_rockchip fe310000.dwmmc: DW MMC controller at irq 25,32 bit host data width,256 deep fifo
[    1.411676] dwmmc_rockchip fe310000.dwmmc: 'clock-freq-min-max' property was deprecated.
[    1.412438] dwmmc_rockchip fe310000.dwmmc: No vmmc regulator found
[    1.413025] dwmmc_rockchip fe310000.dwmmc: No vqmmc regulator found
[    1.414420] dwmmc_rockchip fe320000.dwmmc: IDMAC supports 32-bit address mode.
[    1.415121] dwmmc_rockchip fe320000.dwmmc: Using internal DMA controller.
[    1.415724] dwmmc_rockchip fe320000.dwmmc: Version ID is 270a
[    1.416284] dwmmc_rockchip fe320000.dwmmc: DW MMC controller at irq 26,32 bit host data width,256 deep fifo
[    1.417155] dwmmc_rockchip fe320000.dwmmc: 'clock-freq-min-max' property was deprecated.
[    1.418275] rockchip-iodomain ff770000.syscon:io-domains: Setting to 3000000 done
[    1.418956] rockchip-iodomain ff770000.syscon:io-domains: Setting to 3000000 done
[    1.429835] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    1.441033] dwmmc_rockchip fe320000.dwmmc: 1 slots initialized
[    1.442002] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.444242] sdhci-arasan fe330000.sdhci: No vmmc regulator found
[    1.444783] sdhci-arasan fe330000.sdhci: No vqmmc regulator found
[    1.471964] mmc1: SDHCI controller on fe330000.sdhci [fe330000.sdhci] using ADMA
[    1.474437] ledtrig-cpu: registered to indicate activity on CPUs
[    1.475151] hidraw: raw HID events driver (C) Jiri Kosina
[    1.476232] usbcore: registered new interface driver usbhid
[    1.476730] usbhid: USB HID core driver
[    1.477980] rockchip-dmc dmc: unable to get devfreq-event device : dfi
[    1.482142] rt5651 1-001a: Device with ID register 0x0 is not rt5651
[    1.487342] NET: Registered protocol family 10
[    1.488627] NET: Registered protocol family 17
[    1.489272] Bluetooth: RFCOMM TTY layer initialized
[    1.489713] Bluetooth: RFCOMM socket layer initialized
[    1.490219] Bluetooth: RFCOMM ver 1.11
[    1.490590] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    1.491144] Bluetooth: HIDP socket layer initialized
[    1.491646] [WLAN_RFKILL]: Enter rfkill_wlan_init
[    1.492371] [WLAN_RFKILL]: Enter rfkill_wlan_probe
[    1.492841] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = ap6212
[    1.493448] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
[    1.494097] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
[    1.494828] [WLAN_RFKILL]: wlan_platdata_parse_dt: get property: WIFI,host_wake_irq = 3, flags = 0.
[    1.495625] [WLAN_RFKILL]: wlan_platdata_parse_dt: The ref_wifi_clk not found !
[    1.496273] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
[    1.496743] [WLAN_RFKILL]: Exit rfkill_wlan_probe
[    1.497214] [BT_RFKILL]: Enter rfkill_rk_init
[    1.497990] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 83.
[    1.498737] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 9.
[    1.499470] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 90.
[    1.500201] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 4.
[    1.501491] [BT_RFKILL]: Request irq for bt wakeup host
[    1.502041] [BT_RFKILL]: ** disable irq
[    1.502513] [BT_RFKILL]: bt shut off power
[    1.523958] [BT_RFKILL]: bt_default device registered.
[    1.524522] Key type dns_resolver registered
[    1.525146] sensor_register_slave:mpu6880_gyro,id=50
[    1.526094] ov4689 1-0036: driver version: 00.01.01
[    1.526545] ov4689 1-0036: could not get module information!
[    1.527514] 1-0036 supply avdd not found, using dummy regulator
[    1.528172] 1-0036 supply dovdd not found, using dummy regulator
[    1.528757] 1-0036 supply dvdd not found, using dummy regulator
[    1.531490] ov4689 1-0036: Unexpected sensor id(000000), ret(-5)
[    1.532511] ov4689 2-0036: driver version: 00.01.01
[    1.533019] ov4689 2-0036: could not get module information!
[    1.533897] 2-0036 supply avdd not found, using dummy regulator
[    1.534488] 2-0036 supply dovdd not found, using dummy regulator
[    1.535114] 2-0036 supply dvdd not found, using dummy regulator
[    1.537861] ov4689 2-0036: Unexpected sensor id(000000), ret(-5)
[    1.539010] ov13850 1-0010: driver version: 00.01.01
[    1.539465] ov13850 1-0010: could not get module information!
[    1.540188] 1-0010 supply avdd not found, using dummy regulator
[    1.540790] 1-0010 supply dovdd not found, using dummy regulator
[    1.541376] 1-0010 supply dvdd not found, using dummy regulator
[    1.543658] ov13850 1-0010: Unexpected sensor id(000000), ret(-5)
[    1.544624] ov13850 2-0010: driver version: 00.01.01
[    1.545092] ov13850 2-0010: could not get module information!
[    1.545832] 2-0010 supply avdd not found, using dummy regulator
[    1.546418] 2-0010 supply dovdd not found, using dummy regulator
[    1.547023] 2-0010 supply dvdd not found, using dummy regulator
[    1.549202] mmc1: new HS200 MMC card at address 0001
[    1.549653] ov13850 2-0010: Unexpected sensor id(000000), ret(-5)
[    1.550623] Error: Driver 'sc031gs' is already registered, aborting...
[    1.550813] mmcblk1: mmc1:0001 AJTD4R 14.6 GiB 
[    1.551549] mmcblk1boot0: mmc1:0001 AJTD4R partition 1 4.00 MiB
[    1.552142] mmcblk1boot1: mmc1:0001 AJTD4R partition 2 4.00 MiB
[    1.552759] mmcblk1rpmb: mmc1:0001 AJTD4R partition 3 4.00 MiB
[    1.553578] Registered cp15_barrier emulation handler
[    1.554160] Registered setend emulation handler
[    1.555315] registered taskstats version 1
[    1.555698] Loading compiled-in X.509 certificates
[    1.556125]  mmcblk1: p1 p2 p3 p4 p5 p6 p7 p8 p9
[    1.557298] rga2: Module initialized.
[    1.558965] phy phy-ff770000.syscon:usb2-phy@e450.7: Failed to get VBUS supply regulator
[    1.561821] rockchip-drm display-subsystem: defer getting devfreq
[    1.562729] rockchip-vop ff900000.vop: missing rockchip,grf property
[    1.563643] rockchip-drm display-subsystem: bound ff900000.vop (ops 0xffffff8008c98590)
[    1.564417] rockchip-vop ff8f0000.vop: missing rockchip,grf property
[    1.565200] rockchip-drm display-subsystem: bound ff8f0000.vop (ops 0xffffff8008c98590)
[    1.566194] rockchip-dp ff970000.edp: no DP phy configured
[    1.567465] i2c i2c-9: of_i2c: modalias failure on /edp@ff970000/ports
[    1.568217] rockchip-drm display-subsystem: bound ff970000.edp (ops 0xffffff8008c8fd78)
[    1.569234] dwhdmi-rockchip ff940000.hdmi: Detected HDMI TX controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY)
[    1.571796] rockchip-drm display-subsystem: bound ff940000.hdmi (ops 0xffffff8008c8dd20)
[    1.573144] i2c i2c-10: of_i2c: modalias failure on /dp@fec00000/ports
[    1.574204] cdn-dp fec00000.dp: Direct firmware load for rockchip/dptx.bin failed with error -2
[    1.575003] cdn-dp fec00000.dp: Falling back to user helper
[    1.575188] rockchip-drm display-subsystem: bound fec00000.dp (ops 0xffffff8008c8e700)
[    1.575195] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    1.575197] [drm] No driver support for vblank timestamp query.
[    1.749182] rockchip-vop ff900000.vop: [drm:vop_crtc_enable] Update mode to 1920x1080p60, type: 14
[    1.749827] rockchip-vop ff8f0000.vop: [drm:vop_crtc_enable] Update mode to 1920x1080p60, type: 11
[    1.757137] rockchip-dp ff970000.edp: Rx Max Link Rate is abnormal :80 !
[    1.757148] rockchip-dp ff970000.edp: Rx Max Lane count is abnormal :0 !
[    1.760084] rockchip-dp ff970000.edp: LT link start failed!
[    1.760096] rockchip-dp ff970000.edp: eDP link training failed (-121)
[    1.764873] rockchip-iodomain ff770000.syscon:io-domains: Setting to 3000000 done
[    1.765475] rockchip-iodomain ff770000.syscon:io-domains: Setting to 1800000 done
[    1.768999] rockchip-dp ff970000.edp: LT link start failed!
[    1.769011] rockchip-dp ff970000.edp: eDP link training failed (-121)
[    1.774387] rockchip-dp ff970000.edp: AUX CH command reply failed!
[    1.774881] rockchip-dp ff970000.edp: LT link start failed!
[    1.774886] rockchip-dp ff970000.edp: eDP link training failed (-121)
[    1.777435] rockchip-dp ff970000.edp: AUX CH command reply failed!
[    1.780628] rockchip-dp ff970000.edp: AUX CH command reply failed!
[    1.780632] rockchip-dp ff970000.edp: LT link start failed!
[    1.780636] rockchip-dp ff970000.edp: eDP link training failed (-110)
[    1.783418] rockchip-dp ff970000.edp: AUX CH command reply failed!
[    1.783664] rockchip-dp ff970000.edp: LT link start failed!
[    1.783669] rockchip-dp ff970000.edp: eDP link training failed (-121)
[    1.783812] rockchip-dp ff970000.edp: unable to do link train
[    1.787460] mmc_host mmc0: Bus speed (slot 0) = 150000000Hz (slot req 150000000Hz, actual 150000000HZ div = 0)
[    1.819497] Freeing drm_logo memory: 2252K
[    1.895364] Console: switching to colour frame buffer device 240x67
[    1.964918] rockchip-drm display-subsystem: fb0:  frame buffer device
[    1.972917] mali ff9a0000.gpu: leakage=24
[    1.977664] mali ff9a0000.gpu: Failed to get pvtm
[    1.978844] mali ff9a0000.gpu: avs=0
[    1.980392] mali ff9a0000.gpu: GPU identified as 0x0860 r2p0 status 0
[    1.981498] mali ff9a0000.gpu: Protected mode not available
[    1.983030] mali ff9a0000.gpu: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0
[    1.983753] mali ff9a0000.gpu: Using configured power model mali-simple-power-model, and fallback mali-simple-power-model
[    1.984986] I : [File] : drivers/gpu/arm/midgard/backend/gpu/mali_kbase_devfreq.c; [Line] : 423; [Func] : kbase_devfreq_init(); success initing power_model_simple.
[    1.987249] mali ff9a0000.gpu: Probed as mali0
[    1.993172] xhci-hcd xhci-hcd.8.auto: xHCI Host Controller
[    1.993706] xhci-hcd xhci-hcd.8.auto: new USB bus registered, assigned bus number 3
[    1.994640] xhci-hcd xhci-hcd.8.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x06030010
[    1.995505] xhci-hcd xhci-hcd.8.auto: irq 231, io mem 0xfe800000
[    1.996423] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[    1.997055] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.997708] usb usb3: Product: xHCI Host Controller
[    1.998171] usb usb3: Manufacturer: Linux 4.4.179 xhci-hcd
[    1.998667] usb usb3: SerialNumber: xhci-hcd.8.auto
[    1.999986] hub 3-0:1.0: USB hub found
[    2.000372] hub 3-0:1.0: 1 port detected
[    2.001266] xhci-hcd xhci-hcd.8.auto: xHCI Host Controller
[    2.001803] xhci-hcd xhci-hcd.8.auto: new USB bus registered, assigned bus number 4
[    2.002584] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    2.003547] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[    2.004176] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.004837] usb usb4: Product: xHCI Host Controller
[    2.005285] usb usb4: Manufacturer: Linux 4.4.179 xhci-hcd
[    2.005795] usb usb4: SerialNumber: xhci-hcd.8.auto
[    2.007056] hub 4-0:1.0: USB hub found
[    2.007436] hub 4-0:1.0: 1 port detected
[    2.010123] xhci-hcd xhci-hcd.8.auto: remove, state 1
[    2.010608] usb usb4: USB disconnect, device number 1
[    2.017626] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller
[    2.018153] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus number 5
[    2.019005] xhci-hcd xhci-hcd.9.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x06030010
[    2.019839] xhci-hcd xhci-hcd.9.auto: irq 232, io mem 0xfe900000
[    2.020618] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[    2.021239] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.021889] usb usb5: Product: xHCI Host Controller
[    2.022329] usb usb5: Manufacturer: Linux 4.4.179 xhci-hcd
[    2.022825] usb usb5: SerialNumber: xhci-hcd.9.auto
[    2.023818] hub 5-0:1.0: USB hub found
[    2.024184] hub 5-0:1.0: 1 port detected
[    2.024900] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller
[    2.025396] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus number 6
[    2.026197] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[    2.027038] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003
[    2.027643] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.028302] usb usb6: Product: xHCI Host Controller
[    2.028641] vendor storage:20190527 ret = 0
[    2.029139] usb usb6: Manufacturer: Linux 4.4.179 xhci-hcd
[    2.029626] usb usb6: SerialNumber: xhci-hcd.9.auto
[    2.031258] hub 6-0:1.0: USB hub found
[    2.031666] hub 6-0:1.0: 1 port detected
[    2.035718] xhci-hcd xhci-hcd.8.auto: Host not halted after 16000 microseconds.
[    2.035900] ehci-platform fe380000.usb: EHCI Host Controller
[    2.035942] ehci-platform fe380000.usb: new USB bus registered, assigned bus number 7
[    2.036156] ehci-platform fe380000.usb: irq 28, io mem 0xfe380000
[    2.038108] xhci-hcd xhci-hcd.8.auto: Host controller not halted, aborting reset.
[    2.038825] xhci-hcd xhci-hcd.8.auto: USB bus 4 deregistered
[    2.039366] xhci-hcd xhci-hcd.8.auto: remove, state 1
[    2.039853] usb usb3: USB disconnect, device number 1
[    2.041519] xhci-hcd xhci-hcd.8.auto: USB bus 3 deregistered
[    2.042823] ehci-platform fe380000.usb: USB 2.0 started, EHCI 1.00
[    2.043745] usb usb7: New USB device found, idVendor=1d6b, idProduct=0002
[    2.044422] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.045092] usb usb7: Product: EHCI Host Controller
[    2.045542] usb usb7: Manufacturer: Linux 4.4.179 ehci_hcd
[    2.046058] usb usb7: SerialNumber: fe380000.usb
[    2.047603] hub 7-0:1.0: USB hub found
[    2.048125] hub 7-0:1.0: 1 port detected
[    2.050227] ohci-platform fe3a0000.usb: Generic Platform OHCI controller
[    2.050883] ohci-platform fe3a0000.usb: new USB bus registered, assigned bus number 3
[    2.051812] ohci-platform fe3a0000.usb: irq 29, io mem 0xfe3a0000
[    2.107438] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    2.108091] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.108741] usb usb3: Product: Generic Platform OHCI controller
[    2.109303] usb usb3: Manufacturer: Linux 4.4.179 ohci_hcd
[    2.109822] usb usb3: SerialNumber: fe3a0000.usb
[    2.111681] hub 3-0:1.0: USB hub found
[    2.112115] hub 3-0:1.0: 1 port detected
[    2.114191] input: adc-keys as /devices/platform/adc-keys/input/input1
[    2.117348] dwmmc_rockchip fe310000.dwmmc: IDMAC supports 32-bit address mode.
[    2.118081] dwmmc_rockchip fe310000.dwmmc: Using internal DMA controller.
[    2.118704] dwmmc_rockchip fe310000.dwmmc: Version ID is 270a
[    2.119293] dwmmc_rockchip fe310000.dwmmc: DW MMC controller at irq 25,32 bit host data width,256 deep fifo
[    2.120221] dwmmc_rockchip fe310000.dwmmc: 'clock-freq-min-max' property was deprecated.
[    2.121054] dwmmc_rockchip fe310000.dwmmc: No vmmc regulator found
[    2.121618] dwmmc_rockchip fe310000.dwmmc: No vqmmc regulator found
[    2.122995] dwmmc_rockchip fe310000.dwmmc: allocated mmc-pwrseq
[    2.133989] mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    2.146234] dwmmc_rockchip fe310000.dwmmc: 1 slots initialized
[    2.148031] rockchip-dmc dmc: Failed to get leakage
[    2.148564] rockchip-dmc dmc: Failed to get pvtm
[    2.149754] rockchip-dmc dmc: avs=0
[    2.150187] rockchip-dmc dmc: failed to get vop pn to msch rl
[    2.151080] rockchip-dmc dmc: l=-2147483648 h=2147483647 hyst=0 l_limit=0 h_limit=0
[    2.151837] rockchip-dmc dmc: could not find power_model node
[    2.154074] asoc-simple-card hdmi-sound: i2s-hifi <-> ff8a0000.i2s mapping ok
[    2.159279] asoc-simple-card spdif-sound: dit-hifi <-> ff870000.spdif mapping ok
[    2.163306] input: gpio-keys as /devices/platform/gpio-keys/input/input2
[    2.166899] rk808-rtc rk808-rtc: setting system clock to 2023-03-21 13:18:58 UTC (1679404738)
[    2.168960] rkisp1 ff910000.rkisp1: rkisp1 driver version: v00.01.04
[    2.169576] rkisp1 ff910000.rkisp1: Missing rockchip,grf property
[    2.175554] rkisp1 ff920000.rkisp1: rkisp1 driver version: v00.01.04
[    2.176226] rkisp1 ff920000.rkisp1: Missing rockchip,grf property
[    2.177323] mmc2: queuing unknown CIS tuple 0x80 (2 bytes)
[    2.179517] mmc2: queuing unknown CIS tuple 0x80 (3 bytes)
[    2.181709] mmc2: queuing unknown CIS tuple 0x80 (3 bytes)
[    2.185212] mmc2: queuing unknown CIS tuple 0x80 (7 bytes)
[    2.189293] mmc2: queuing unknown CIS tuple 0x81 (9 bytes)
[    2.209609] rkisp1 ff910000.rkisp1: clear unready subdev num: 3
[    2.210522] rockchip-mipi-dphy-rx: No link between dphy and sensor
[    2.211089] rockchip-mipi-dphy-rx: No link between dphy and sensor
[    2.211638] rkisp1: update sensor failed
[    2.212004] rkisp1 ff920000.rkisp1: clear unready subdev num: 2
[    2.212734] rockchip-mipi-dphy-rx: No link between dphy and sensor
[    2.213294] rockchip-mipi-dphy-rx: No link between dphy and sensor
[    2.213860] rkisp1: update sensor failed
[    2.214804] ALSA device list:
[    2.215079]   #0: rockchip,hdmi
[    2.215362]   #1: ROCKCHIP,SPDIF
[    2.279280] mmc_host mmc2: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[    2.284988] mmc2: new high speed SDIO card at address 0001
[    2.434769] dwmmc_rockchip fe320000.dwmmc: Successfully tuned phase to 193
[    2.435494] mmc0: new ultra high speed SDR104 SDXC card at address 0001
[    2.438274] mmcblk0: mmc0:0001 EC2QT 59.6 GiB 
[    2.440649]  mmcblk0: p1 p2
[    2.682286] phy phy-ff770000.syscon:usb2-phy@e450.7: charger = USB_FLOATING_CHARGER
[    2.684632] Freeing unused kernel memory: 1088K
Loading, please wait...
starting version 229
[    2.731150] random: systemd-udevd: uninitialized urandom read (16 bytes read, 38 bits of entropy available)
[    2.732435] random: systemd-udevd: uninitialized urandom read (16 bytes read, 38 bits of entropy available)
[    2.733371] random: systemd-udevd: uninitialized urandom read (16 bytes read, 38 bits of entropy available)
[    2.734308] random: systemd-udevd: uninitialized urandom read (16 bytes read, 38 bits of entropy available)
[    2.734462] random: udevadm: uninitialized urandom read (16 bytes read, 38 bits of entropy available)
[    2.734597] random: udevadm: uninitialized urandom read (16 bytes read, 38 bits of entropy available)
[    2.734631] random: udevadm: uninitialized urandom read (16 bytes read, 38 bits of entropy available)
[    2.734695] random: udevadm: uninitialized urandom read (16 bytes read, 38 bits of entropy available)
[    2.734980] random: udevadm: uninitialized urandom read (16 bytes read, 38 bits of entropy available)
[    2.735043] random: udevadm: uninitialized urandom read (16 bytes read, 38 bits of entropy available)
[    2.884674] cdn-dp fec00000.dp: [drm:cdn_dp_request_firmware] *ERROR* failed to request firmware: -11
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.27.1
[/sbin/fsck.ext4 (1) -- /dev/mmcblk0p2] fsck.ext4 -a -C0 /dev/mmcblk0p2 
rootfs: clean, 31534/54432 files, 161620/217600 blocks
done.
[    3.058720] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
Begin: Resizing ext4 file system on /dev/mmcblk0p2 ... resize2fs 1.42.13 (17-May-2015)
Resizing the filesystem on /dev/mmcblk0p2 to 220160 (4k) blocks.
The filesystem on /dev/mmcblk0p2 is now 220160 (4k) blocks long.

done.
[    3.225314] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
[    3.501852] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN)
[    3.505918] systemd[1]: Detected architecture arm64.

Welcome to Ubuntu 16.04.2 LTS!

[    3.513315] systemd[1]: Set hostname to <FriendlyELEC>.
[    3.805139] systemd[1]: Listening on udev Kernel Socket.
[  OK  ] Listening on udev Kernel Socket.
[    3.807213] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[  OK  ] Set up automount Arbitrary Executab...ats File System Automount Point.
[    3.809194] systemd[1]: Created slice User and Session Slice.
[  OK  ] Created slice User and Session Slice.
[    3.810309] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[  OK  ] Started Forward Password Requests to Wall Directory Watch.
[    3.811550] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[  OK  ] Started Dispatch Password Requests to Console Directory Watch.
[    3.813024] systemd[1]: Listening on udev Control Socket.
[  OK  ] Listening on udev Control Socket.
[    3.814322] systemd[1]: Listening on Journal Audit Socket.
[  OK  ] Listening on Journal Audit Socket.
[    3.815420] systemd[1]: Listening on Journal Socket.
[  OK  ] Listening on Journal Socket.
[    3.816347] systemd[1]: Listening on Journal Socket (/dev/log).
[  OK  ] Listening on Journal Socket (/dev/log).
[    3.817356] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[  OK  ] Listening on /dev/initctl Compatibility Named Pipe.
[    3.818447] systemd[1]: Reached target Paths.
[  OK  ] Reached target Paths.
[    3.819420] systemd[1]: Reached target Remote File Systems (Pre).
[  OK  ] Reached target Remote File Systems (Pre).
[    3.820387] systemd[1]: Reached target Remote File Systems.
[  OK  ] Reached target Remote File Systems.
[    3.821970] systemd[1]: Created slice System Slice.
[  OK  ] Created slice System Slice.
[    3.825507] systemd[1]: Starting Remount Root and Kernel File Systems...
         Starting Remount Root and Kernel File Systems...
[    3.829516] systemd[1]: Mounting Huge Pages File System...
         Mounting Huge Pages File System...
[    3.835504] systemd[1]: Mounting Debug File System...
         Mounting Debug File System...
[    3.836437] systemd[1]: Reached target Slices.
[  OK  ] Reached target Slices.
[    3.837849] systemd[1]: Created slice system-serial\x2dgetty.slice.
[  OK  ] Created slice system-serial\x2dgetty.slice.
[    3.841346] systemd[1]: Mounting POSIX Message Queue File System...
         Mounting POSIX Message Queue File System...
[    3.849047] systemd[1]: Starting Load Kernel Modules...
         Starting Load Kernel Modules...
[    3.855179] systemd[1]: Starting Journal Service...
         Starting Journal Service...
[    3.858392] systemd[1]: Starting Set console keymap...
         Starting Set console keymap...
[    3.861975] systemd[1]: Starting Create list of required static device nodes for the current kernel...
         Starting Create list of required st... nodes for the current kernel...
[    3.863413] systemd[1]: Reached target Encrypted Volumes.
[  OK  ] Reached target Encrypted Volumes.
[    3.864664] systemd[1]: Reached target Swap.
[  OK  ] Reached target Swap.
[    3.871610] systemd[1]: Mounted Debug File System.
[  OK  ] Mounted Debug File System.
[    3.872592] systemd[1]: Mounted POSIX Message Queue File System.
[  OK  ] Mounted POSIX Message Queue File System.
[    3.873427] systemd[1]: Mounted Huge Pages File System.
[  OK  ] Mounted Huge Pages File System.
[    3.875284] systemd[1]: Started Remount Root and Kernel File Systems.
[  OK  ] Started Remount Root and Kernel File Systems.
[    3.878800] systemd[1]: Started Load Kernel Modules.
[  OK  ] Started Load Kernel Modules.
[    3.880748] systemd[1]: Started Create list of required static device nodes for the current kernel.
[  OK  ] Started Create list of required sta...ce nodes for the current kernel.
[    3.882471] random: nonblocking pool is initialized
[    3.969123] systemd[1]: Started Set console keymap.
[  OK  ] Started Set console keymap.
[    4.010427] systemd[1]: Starting Create Static Device Nodes in /dev...
         Starting Create Static Device Nodes in /dev...
[    4.013126] systemd[1]: Mounting Configuration File System...
         Mounting Configuration File System...
[    4.016011] systemd[1]: Starting Apply Kernel Variables...
         Starting Apply Kernel Variables...
[    4.018737] systemd[1]: Mounting FUSE Control File System...
         Mounting FUSE Control File System...
[    4.023290] systemd[1]: Starting udev Coldplug all Devices...
         Starting udev Coldplug all Devices...
[    4.026101] systemd[1]: Starting Load/Save Random Seed...
         Starting Load/Save Random Seed...
[    4.030563] systemd[1]: Mounted Configuration File System.
[  OK  ] Mounted Configuration File System.
[    4.032976] systemd[1]: Mounted FUSE Control File System.
[  OK  ] Mounted FUSE Control File System.
[    4.034084] systemd[1]: Started Journal Service.
[  OK  ] Started Journal Service.
[  OK  ] Started Apply Kernel Variables.
[  OK  ] Started Load/Save Random Seed.
[  OK  ] Started Create Static Device Nodes in /dev.
         Starting udev Kernel Device Manager...
[  OK  ] Reached target Local File Systems (Pre).
         Starting Flush Journal to Persistent Storage...
[  OK  ] Started Flush Journal to Persistent Storage.
[  OK  ] Started udev Coldplug all Devices.
[  OK  ] Started udev Kernel Device Manager.
[  OK  ] Created slice system-systemd\x2dbacklight.slice.
         Starting Load/Save Screen Backlight...htness of backlight:backlight...
[  OK  ] Started Load/Save Screen Backlight Brightness of backlight:backlight.
[  OK  ] Found device /dev/mmcblk0p1.
[  OK  ] Found device /dev/ttyFIQ0.
[  OK  ] Reached target Sound Card.
         Mounting /mnt/sdcard...
[  OK  ] Found device /sys/subsystem/net/devices/eth0.
[  OK  ] Mounted /mnt/sdcard.
[  OK  ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch.
[  OK  ] Reached target Local File Systems.
[  OK  ] Started ifup for eth0.
         Starting Create Volatile Files and Directories...
         Starting Raise network interfaces...
         Starting Set console font and keymap...
[  OK  ] Started Create Volatile Files and Directories.
         Starting Network Time Synchronization...
         Starting Update UTMP about System Boot/Shutdown...
         Starting Load/Save RF Kill Switch Status...
[    4.737215] [dhd] dhd_conf_set_chiprev : devid=0xa9a6, chip=0xa9a6, chiprev=1
[  OK  ] Started Network Time Synchronization.
[  OK  ] Started Update UTMP about System Boot/Shutdown.
[  OK  ] Reached target System Time Synchronized.
[  OK  ] Reached target System Initialization.
[  OK  ] Started Daily apt activities.
[  OK  ] Listening on D-Bus System Message Bus Socket.
[  OK  ] Reached target Sockets.
[  OK  ] Started Daily Cleanup of Temporary Directories.
[  OK  ] Reached target Timers.
[  OK  ] Reached target Basic System.
         Starting HDMI-force-ON...
         Starting Permit User Sessions...
[  OK  ] Started D-Bus System Message Bus.
         Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"...
         Starting Save/Restore Sound Card State...
         Starting LSB: fast remote file copy program daemon...
         Starting Login Service...
         Starting Restore /etc/resolv.conf i...re the ppp link was shut down...
[  OK  ] Started Load/Save RF Kill Switch Status.
[  OK  ] Started Set console font and keymap.
[  OK  ] Started HDMI-force-ON.
[  OK  ] Started Permit User Sessions.
[  OK  ] Started LSB: fast remote file copy program daemon.
[  OK  ] Started Restore /etc/resolv.conf if...fore the ppp link was shut down.
[  OK  ] Started Save/Restore Sound Card State.
[  OK  ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand".
[  OK  ] Started ifup for wlan0.
         Starting Daily apt activities...
         Starting Set console scheme...
[  OK  ] Created slice system-getty.slice.
[  OK  ] Started Login Service.
[  OK  ] Started Set console scheme.
[    5.141637] [dhd][wlan0] wl_android_wifi_on : in g_wifi_on=0
[    5.949603] [dhd] dhd_conf_read_config : Ignore config file /system/etc/firmware/config.txt
[    5.950458] [dhd] dhd_conf_set_path_params : Final fw_path=/system/etc/firmware/fw_bcm43438a1.bin
[    5.951307] [dhd] dhd_conf_set_path_params : Final nv_path=/system/etc/firmware/nvram_ap6212a.txt
[    5.952115] [dhd] dhd_conf_set_path_params : Final clm_path=/system/etc/firmware/clm_bcm43438a1.blob
[    5.952989] [dhd] dhd_conf_set_path_params : Final conf_path=/system/etc/firmware/config.txt
[    6.160050] [dhd] dhd_conf_set_txglom_params : txglom_mode=multi-desc
[    6.160621] [dhd] dhd_conf_set_txglom_params : txglomsize=36, deferred_tx_len=0
[    6.161321] [dhd] dhd_conf_set_txglom_params : txinrx_thres=-1, dhd_txminmax=1
[    6.161994] [dhd] dhd_conf_set_txglom_params : tx_max_offset=0, txctl_tmo_fix=300
[    6.162664] [dhd] dhd_conf_get_disable_proptx : fw_proptx=1, disable_proptx=-1
[    6.228997] [dhd] dhd_conf_set_country : set country CN, revision 0
[    6.233334] [dhd] dhd_conf_set_country : Country code: CN (CN/0)
[    6.241279] [dhd] CONFIG-ERROR) dhd_conf_set_intiovar : ampdu_mpdu setting failed -29
[    6.242047] [dhd][wlan0] wl_android_wifi_on : Success
[  OK  ] Started Raise network interfaces.
[  OK  ] Reached target Network.
[  OK  ] Reached target Network is Online.
         Starting /etc/rc.local Compatibility...
         Starting LSB: disk temperature monitoring daemon...
         Starting OpenBSD Secure Shell server...
[  OK  ] Started LSB: disk temperature monitoring daemon.
[  OK  ] Started /etc/rc.local Compatibility.
[  OK  ] Started Getty on tty2.
         Starting eflasher-gui...
[  OK  ] Started Serial Getty on ttyFIQ0.
[  OK  ] Reached target Login Prompts.
[  OK  ] Started OpenBSD Secure Shell server.
[  OK  ] Started Daily apt activities.

Ubuntu 16.04.3 LTS NanoPi-NEO4 ttyFIQ0

NanoPi-NEO4 login: 
